|
BUSHINGS | Top |
| Description |
Buy |
BUSHING FRONT PUMP BABBIT
image #034 Item #44034 | | BUSHING Pump Teflon coated (SONNAX) (performance)
image #034 Item #44034T | | BUSHING FRONT PUMP (DURA BOND SOLID COATED) TH350, TH400, TH425, 4L30E, TH180, TH325, ST300, AT540, ALUMINUM POWER GLIDE
image #034 Item #DB44034 | | BUSHING PUMP BABBIT (ROLLED METAL)
image #034 Item #8005 | | BUSHING STATOR FRONT 30 SPLINE INPUT (.655" WIDE) (1.00" ID) TH350, 700-R4, 4L60E (ALL)
image #036 Item #44036B | | BUSHING STATOR FRONT 350 69-86 700R4, 4L60E (.485" WIDE) (1.00" ID)
image #036 Item #44036 | | BUSHING (STATOR REAR 350 69-86 (uses two)) (200-4R CENTER SUPPORT) (each)
image #037, 044 Item #44037 | | BUSHING DIRECT DRUM (NARROW BRONZE) 350
image #046 Item #44046B | | BUSHING DIRECT DRUM WIDE NO GROOVES TH350
image #046 Item #44046C | | Bushing, Direct Drum 85-UP (Toyota A340, A340E, A340F, A340H, A341E, A343F, A650E, A350, JEEP AW)
image #046 Item #97046 | | BUSHING INPUT RING GEAR (Babbit) 350 69-86
image #050 Item #44050 | | BUSHING INPUT RING GEAR HUB TH350 69-85
image #050 Item #44050B | | BUSHING, SUN GEAR and REAR PLANET 350 69-86
image #052 Item #44052 | | BUSHING OUTPUT SHAFT TH350 (Bronze) more>>
image #062 Item #44062 | | BUSHING OUTPUT TEFLON 350
image #062 Item #44062C | | BUSHING CASE BRONZE TH350, TH700-R4, 4L60/65E 1969-UP
image #064 Item #74064 | | BUSHING CASE BABBITT TH350 TH700-R4
image #064 Item #44064 | | BUSHING CASE (DURA-BOND SOLID) BABBITT TH350 TH700-R4
image #064 Item #DB44064 | | BUSHING EXTENSION HOUSING BRONZE (1.630"OD, .940" Tall)
image #066 Item #44066B | | BUSHING EXTENSION HOUSING BABBIT (1.630"OD, .940" Tall)
image #066 Item #44066 | | BUSHING EXTENSION HOUSING TEFLON COATED
image #066 Item #74066T | | BUSHING TAIL HOUSING, Transfer Case, (slip yoke type) (2.010" O.D.) NP208, NP231, NP233, NP236, NP241, NP243, NP246, NP261 with 32 SPLINE OUTPUT, some NP263 (with Slip yoke type)
image #066 Item #331066 | |
ELECTRICAL SOLENOIDS, SENSORS, etc. | Top |
| Description |
Buy |
PRESS SWITCH, 44psi. LOCKUP GOVERNOR TH350C
image #416 Item #44416AA | | PRESS SWITCH, 50psi. LOCKUP GOVERNOR TH350C
image #416 Item #44416D | | PRESSURE SWITCH, TH350 52psi. LOCKUP GOVERNOR PRESS SWITCH
image #416 Item #44416E | | TCC SOLENOID UNIVERSAL TH350C 1980-ON
image #425 Item #A44425U | | CONNECTOR 4 PIN SQUARE GM UNIVERSAL 2,3, OR 4 PIN
image #444 Item #84444U | | CONNECTOR, Square Plug - Case Connector 3 Prong (O-Ring 44369B Not Included) THM200-4R, 4L30-E, THM700-R4, THM125/M34, THM350C, THM700-R4/4L60/MD8, THM125C, 3T40
image #444 Item #74444A | |
GASKETS, O-RINGS & MISC. ITEMS | Top |
| Description |
Buy |
LIP SEAL SPEEDO DRIVE (PACK OF 2)
image #078 Item #44078X | | MODULATOR HOSE 350 69-86 PRE-CUT MOLDED ELBOW
image #162 Item #44162 | | PAN GASKET C/NEO 350/C 69-86
image #300 Item #44300 | | PAN GASKET FIBER 350/C 69-86
image #300 Item #44300F | | Gasket, Bottom Pan (Fiber) ( FOR: A340, A341, A343, AW4, A350, A650E) (85-Up)
image #300 Item #97300F | | GASKET (203) TRANSFER CASE to ADAPTER 350 73-86 (7 BOLT HOLES)
image #304 Item #301304A | | TRANSFER CASE to ADAPTER GASKET ( 6 bolt holes) (208, 241, 242, 246, 261 GM
image #304 Item #331304A | | ADAPTER GASKET -NP205 69-86 (3.450" SMALL HOLE) (8 BOLT HOLES)
image #304 Item #311304 | | Gasket, NP205, Adapter, Large Hole Type (3.855" ID Large Hole) (8 BOLT HOLES)
image #304 Item #311304A | | WASHER FRONT PUMP BOLT 8 per PACK
image #309 Item #44309 | | GASKET FRONT PUMP 350/C 69-86
image #310 Item #44310 | | O-RING SEAL FRONT PUMP TH350, TH400 64-UP
image #311 Item #44311 | | GASKET UPPER V.B. TH250 / TH350 69-79
image #320 Item #44320 | | GASKET UPPER V.B. 250C/350C 80-86
image #320 Item #44320A | | GASKET LOWER V.B. 250/350 69-79
image #321 Item #44321 | | GASKET LOWER V.B. 250C/350C 80-86
image #321 Item #44321A | | GASKET OIL FILTER 350 69-86
image #326 Item #44326 | | GASKET SOLENOID 350/C 80-86
image #328 Item #44328 | | Lip Seal, Intermediate Clutch (Inner) TH350
image #332 Item #44332 | | Lip Seal, Intermediate Clutch (Outer) TH350
image #333 Item #44333 | | LIP SEAL, Forward / Direct clutch piston (outer) (TH400 64-UP) (4L80E 91-96) ( TH350 FORWARD PISTON, outer 69-UP ) (WHEN OUT OF STOCK USE PAPER RUBBER KIT)
image #335 Item #34335 | | Lip Seal, Direct Clutch (center) TH350
image #336 Item #44336C | | Lip Seal, Direct, Forward Clutch (Inner) TH350
image #336 Item #44336 | | Lip Seal, Direct Clutch (Outer) TH350
image #337 Item #44337 | | SEAL LOW / REVERSE (INNER) TH700R4, 4L60E, TH350 / POWERGLIDE ALUM.
image #338 Item #44338 | | SEAL LOW/REVERSE CLUTCH (CENTER) TH700R4, 4L60E, TH350 69-UP
image #338, 339 Item #44339C | | SEAL LOW / REVERSE PISTON (OUTER) TH350 / POWERGLIDE / TH700, 4L60E
image #339 Item #44339 | | SEAL GOVERNOR COVER TH350, 700R4 69-UP
image #345 Item #44345 | | O-RING SEAL CASE to EXTENSION HOUSING: TH350 / ST300 / TH700 / (4L60E 93-96 4 BOLT HOUSING)
image #348 Item #44348 | | O-RING ACCUMULATOR COVER (STEEL COVER) TH350/C TH250/C 1969-86
image #362 Item #44362 | | O-RING ACCUMULATOR COVER (ALUMINUM COVER) TH350/C TH250/C 1969-86 |
image #362 Item #44362A | | O-RING SPEEDO HOUSING (1.875" OD) TH 350 69-UP 700R4 82-93: SOME 4L60E
image #369 Item #44369A | | O-RING SEAL (VARIOUS USE) SPEEDO .750" OD: O-RING SEAL MODULATOR, CASE CONNECTOR
image #369, 368, 346, 347 Item #44369B | | O-RING FILLER TUBE VARIOUS GM/ FORD/ CHRYSLER
image #371 Item #44371A | | MULTI LIP SEAL SLEEVE OIL FILLER TUBE
image #371 Item #44371B | | O-RING DETENT CABLE 350 69-78
image #373 Item #44373A | | DETENT CABLE SLEEVE 350 78-86
image #373 Item #44373B | | O-Ring, Output Shaft Sleeve to Slip-Yoke (350) (69-86), 700-R4, 4L60E (Light Trucks) (82-Up)
image #374 Item #44374B | | O-RING (O-RING REVERSE BAND LEVER SHAFT TF8, A727, A518, 46/47 RE/RH ) (TURBINE SHAFT TH350C / 200c / 325-4L/ 7004R / 4L60E 298MM CONVERTER)
image #380, 384 Item #44380 | | DETENT CABLE (39" Long Conduit, 44" Wire with Metal Slider on top (throttle linkage) end)
image #450 Item #T44450 | | DETENT CABLE (34.5" Long Conduit, 41" Wire with Plastic Tear Drop on throttle linkage end)
image #450 Item #T44450A | | CABLE REPAIR KIT /350
image #451 Item #K35909 | | UNIVERSAL GM DUST COVER
image #463 Item #M463D | | CUP PLUG EXPANSION 3/8" DIAMETER (FOR PARK PIN and VARIOUS USE)
image #483 Item #54483A | | UNIVERSAL FILLER TUBE and STICK (TH350, TH400
image #494 Item #T44494U | | FILLER TUBE REPAIR TIP, ( REPAIR BROKEN OR DAMAGED FILLER TUBE END)
image #494 Item #T44494R | | CHECK BALL STEEL .250" VARIOUS valve bodys (each)
image #741 Item #44741-5 | | Repair Kit, Fixes 5 Valve Body Plate Holes with 1/4" Check Balls, Fits Most Applications
image #747, 741, 740 Item #VB-101 | | CASE SAVER, (4 PIECE SET), TH250, TH250C, TH350, TH350C, TH700R4, 4L60E (69-UP)
image #761, 630, 741 Item #A44761A | | Pan Magnet, Square (.180" Thick, 1.100" x .750")
image #839 Item #A44839 | | Pan Magnet, Round (.250" Thick, 1 3/4" OD)
image #839 Item #A44839B | | SPEEDO DRIVE GEAR 10-TEETH PURPLE
image #847 Item #A44847BC | | SPEEDO DRIVE GEAR 8T-GM BLACK
image #847 Item #A44847AD | | GEAR, GM SPEEDO DRIVE 17T RED TH700-R, TH350
image #847 Item #A44847C | | SPEEDO DRIVE GEAR 7-TEETH RED TH350
image #847 Item #A44847 | | SPEEDO DRIVEN GEAR 18T-GM
.810" OD gear pitch left to right from top down
image #848 Item #A54848A | | SPEEDO DRIVEN GEAR 19T-GM WHITE
.810" OD gear pitch left to right from top down
image #848 Item #A44848 | | SPEEDO DRIVEN GEAR 20T-GM
.810" OD gear pitch left to right from top down
image #848 Item #A44848A | | SPEEDO DRIVEN GEAR (RED) 21T-GM
.810" OD gear pitch right to left from bottom to top
image #848 Item #A44848B | | SPEEDO DRIVEN GEAR 22T-GM
.810" OD gear pitch left to right from top down
image #848 Item #A44848C | | SPEEDO DRIVEN GEAR 24T-GM
.870" OD, gear pitch left to right from top down
image #848 Item #D44848E | | SPEEDO DRIVEN GEAR 24T-GM
.870" OD, gear pitch right to left from top down
image #848 Item #D44848EA | | SPEEDO DRIVEN GEAR 22T-GM
.870" OD, gear pitch right to left from top down
image #848 Item #D44848CB | | SPEEDO DRIVEN GEAR 34T-GM (GREEN)
image #848A Item #A34848A | | SPEEDO DRIVEN GEAR 35T-GM
image #848B Item #A34848B | | SPEEDO DRIVEN GEAR (WHITE) 36T-GM
image #848C Item #A34848C | | SPEEDO DRIVEN GEAR 37T-GM
image #848D Item #A34848D | | SPEEDO DRIVEN GEAR 38T-GM
image #848E Item #A34848E | | SPEEDO DRIVEN GEAR 39T-GM (BROWN)
image #848F Item #A34848F | | SPEEDO DRIVEN GEAR 40T-GM
image #848G Item #A34848G | | SPEEDO DRIVEN GEAR 41T-GM
image #848H Item #A34848H | | SPEEDO DRIVEN GEAR (GREEN) 42T-GM
image #848HA Item #A34848HA | | SPEEDO DRIVEN GEAR 43T-GM
image #848J Item #A34848J | | SPEEDO DRIVEN GEAR (GRAY) 44T-GM
image #848K Item #A34848K | | SPEEDO DRIVEN GEAR 45T-GM
image #848L Item #A34848L | | SPEEDO CLIP (SHORT .401" WIDE) TH350
image #849 Item #M463FB | | SPEEDO CLIP ( NARROW .303" WIDE x .750" LONG ) 180/ 4L30E/ 350/ 700R4
image #849 Item #M463F | | GROMMET, Cross Shaft Linkage (GM) (White plastic half moon)
image #991 Item #M463GB | | SHAFT, MANUAL LEVER SHAFT and INNER LEVER TH350/C 1969-ON
image #991 Item #44991-3 | | Park Rod and Park actuator bracket (USED) TH350 All
image #991 Item #U44991-4 | | BOLT, Torque Converter Bolt M10 x 1.5 x 14.6 mm length ( Hex )
image #997 Item #M464GE | |
HARD PARTS GOOD USED | Top |
| Description |
Buy |
VALVE, (used) Modulator valve TH350 69-UP
img#163 Item #U44163 | | PUMP COVER STATOR (used) TH350C 80-86 lock up
img#520 Item #U44520 | | DRUM, (used) Forward (bare) Drum only (input shaft not included)
img#554 Item #U44554 | | FORWARD DRUM with INPUT SHAFT (used) TH350 69-79 NON LOCKUP
img#554, 670 Item #U44554S | | FORWARD DRUM With SHAFT LOCK-UP (Used) TH350 1980-86
img#554, 670 Item #U44554SA | | DRUM DIRECT CLUTCH: TH350 / TH350C 69-86 (USED)
img#555 Item #U44555 | | PLANET CARRIER (used) FRONT WASHER TYPE 350
img#582 Item #U44582 | | PLANET CARRIER (used) REAR 350 1969-86 (Has polished washer surface works with thrust washer or thrust bearing)
img#584 Item #U44584 | | PLANET CARRIER (used) REAR TH350 1969-86 (Has NON polished thrust surface works with thrust bearing only)
img#584 Item #U44584A | | RING GEAR (FRONT INPUT) (USED) (ONE PIECE HUB and RING GEAR, BEARING TYPE THRUST SURFACE) TH350 1969-UP
img#592 Item #U44592 | | RING GEAR (FRONT INPUT) (TWO PIECE HUB and RING GEAR with Snap Ring, WASHER TYPE SURFACE) TH350
img#592 Item #U44592A | | RING GEAR & HUB (REAR) OUTPUT (3 TAB WASHER #251 TYPE) TH350/C 1969-86
img#594 Item #U44594 | | RING GEAR & HUB (REAR) OUTPUT (Good Used) (BEARING #251 TYPE) 350 69-86
img#594 Item #U44594B | | SUN GEAR, (used) TH350 69-UP
img#612 Item #U44612 | | SHELL ASSYEMBLY (used) with SUN GEAR 350 69-86
img#622, 243, 886, 612 Item #35728AU | | SUPPORT CLIP (ANTI-CLUNK SPRING) (USED) TH350 TH700-R4, 4L60E 69-UP
img#639 Item #U74639 | | RACE, INTERMEDIATE ROLLER CLUTCH (USED) TH350
img#663 Item #U44663 | | LOW ROLLER CLUTCH INNER RACE (used) TH350, TH700-R4, 4L60E (ALL) (when out of stock use R74631A
img#664 Item #U44664 | | SHAFT INPUT (Good Used) 350 NON LOCK-UP bushing type pilot
img#670 Item #U44670 | | SHAFT INPUT(Good Used) LOCK-UP 350 80-86
img#670 Item #U44670B | | SHAFT OUTPUT (used) 4 WHEEL DRIVE (9.625" LENGTH) TH350 69-81
img#678 Item #35738CU | | SHAFT OUTPUT SHORT TAIL (15.500" Long) TH350 69-81 2 Wheel Drive
img#678 Item #U44678 | | COVER GOVERNOR (GOOD USED) (TH350 69-UP) (TH700-R4 82-UP)
img#686 Item #U74686 | | Clip, Governor Cover (69-93)
img#687 Item #U44687 | | VALVE BODY, (good used) does not include the direct accumulator #930
img#740 Item #U44740 | | LEVER, (used) Detent lever and Clip TH350 69-UP (clips on to valve body bracket)
img#744 Item #U44744 | | PLATE, VB separator cover plate (non lockup) TH350 / TH250 1969-79
img#744, 747 Item #U44747P | | EXTENSION HOUSING (used) TH350, TH250 69-UP SHORT TAIL 6" (CHEVROLET, SMALL SPEEDO HOLE .875" DIAMETER)
img#770 Item #U44770A | | EXTENSION HOUSING (used) TH350, TH250 69-UP SHORT TAIL 6" (BUICK, PONTIAC OLDSMOBILE, LARGE SPEEDO HOLE 2.10" DIAMETER)
img#770 Item #U44770 | | BRACKET, (used) SPEEDO HOUSING HOLD DOWN (.275" BOLT HOLE) (LARGE DIAMETER SPEEDO HOUSING) TH400, TH350, TH700R4 4L60E
img#842 Item #U74842 | | BRACKET, (Used) SPEEDO HOUSING HOLD DOWN (SMALL RECTANGULAR HOLD DOWN FOR .875" O.D. Housing) ChevroletTH350
img#842 Item #U44842 | | BRACKET, (used) SPEEDO HOUSING HOLD DOWN (.340" BOLT HOLE) (LARGE DIAMETER SPEEDO HOUSING) TH400, TH350, ST300
img#842 Item #U34842 | | BRACKET MODULATOR, (used) 350 / 350C 68-86
img#843 Item #U44843 | | CUSHON PLATE (Used) INTERMEDIATE 350 69-86
img#852 Item #U44852 | | WAVE PLATE, (used) Forward clutch cushion plate, some direct clutch packs for softer 2-3 shift
img#858 Item #U44858 | | SERVO, (used) Intermediate servo assembly: (late design) Includes #908 #906 #909 #284 #907
img#905, 906, 907, 908, 909, 284 Item #U44905 | | PISTON, (used) Accumulator piston in case TH350 75-UP (can use on early 69-UP units)
img#927 Item #U44927A | | COVER, (used) Accumulator cover (Aluminum cover)
img#929 Item #U44929 | | COVER, (used) Accumulator cover (Steel cover)
img#929 Item #U44929S | | SPRING, DIRECT ACCUMULATOR SPRING (USED) TH350
img#931 Item #U44931 | | PISTON, (used) Direct Accumulator Piston (Aluminum piston only ) (located on the valve body)
img#932, 930 Item #U44932 | | SLEEVE, (used) Output Shaft to Slip-Yoke o-ring sleeve (TH350) (69-86), 2.220" long
img#958 Item #U44958 | | PISTON, Intermediate (V8 1" TALL) (used) TH350 69-UP
img#962 Item #U44962 | | PISTON SET (For V8) 4 Pistons TH350 /TH350C 69-UP
img#962, 964, 965, 966 Item #U44960K | | PISTON, Forward clutch piston V8 Height (used) TH350 1969-ON
img#964 Item #U44964 | | PISTON, (used) High / Reverse Piston TH350, TH350C 1969-ON Direct clutch piston for 4 disc capacity, V8 engines
img#965 Item #U44965 | | PISTON, (used) REVERSE / LOW 2-15/16" TALL TH350 69-UP
img#966 Item #U44966 | | SPRING, (used) Intermediate piston return spring (Each)
img#972 Item #U44972 | | RETAINER, (used) Intermediate piston spring retainer with springs attached, TH350
img#972, 982 Item #U44982A | | RETAINER with Springs, (used) Forward piston spring retainer WITH springs attached, late TH350
img#974 Item #U44974A | | RETAINER, (used) Direct piston spring retainer WITH springs attached, TH350
img#975 Item #U44975A | | SPRING, (used) Direct clutch piston return spring (Each)
img#975 Item #U44975S | | RETAINER, (used) Direct / Forward piston spring retainer WITHOUT springs attached, early TH350
img#975, 974 Item #U44975 | | RETAINER LOW /REVERSE (good used) (With SPRINGS ATTACHED) TH350/C TH700-R4, 4L60E
img#977 Item #U74977 | | SPRING RETAINER LOW /REVERSE (NEW OE) (With SPRINGS ATTACHED) TH350/C TH700-R4, 4L60E
img#977 Item #D74977 | | RETAINER (Good Used) for INTERMEDIATE CLUTCH ROLLER 350
img#980 Item #U44980 | | RETAINER, (used) Intermediate piston spring retainer without springs, TH350 69-73
img#982 Item #U44982 | | DETENT LINKAGE WIRE LINK, (USED) TH350/C TH250/C 1969 UP
img#997 Item #U44997 | |
SEALING RINGS & RING KITS | Top |
| Description |
Buy |
SEALING RING KIT COMPLETE (73-86) TH350 (WILL FIT 69-72 EXCEPT THE ACCUMULATOR RINGS ARE DIFFERENT)
img#175, 179, 181, 177, 192,191, 195 Item #44175A | | SEALING, RING KIT 350 74-86 (TEFLON RINGS) will fit 69-up (does not fit early 1-2 accumulator piston outer ring)
img#175, 179, 181, 192,191, 195 Item #44175BT | | SEALING RING KIT STATOR ONLY 350/ 350C: FIVE STATOR RINGS 69-86
img#175,179, 181 Item #44175 | |
TORQUE CONVERTERS reman | Top |
| Description |
Buy |
|
Torque Converter select returned 11 rows.
| Torque Converter (remanufactured) 12.4" Diameter (2000 Stall) (Chevrolet Brackets no threads)
Add an addition refundable core charge of $65.00
Item #DC10SS | | TC 13" DIAMETER, L6 V8, THREAD 10mm X 1.5, STALL 16K-18K, 10.750" BOLT CIRCLE, LOCK-UP
Add an addition refundable core charge of $85.00
Item #GM16 | | TC 13" DIAMETER, V8, THREAD 10mm X 1.5, STALL 14K-16K, 10.750" BOLT CIRCLE, DUMMY LOCK-UP LOCK-UP CLUTCH REMOVED,
(USE WITH LOCK-UP INPUT SHAFT "SMOOTH TIP")
Add an addition refundable core charge of $45.00
Item #GM160 | | TC 13" DIAMETER, L6 V8, THREAD 10mm X 1.5, HIGH STALL 18K-20K, 10.750" BOLT CIRCLE, LOCK-UP
Add an addition refundable core charge of $45.00
Item #GM16AH | | TC 12" DIAMETER. L6 V8 FIXED PITCH STATOR, STALL 16K-18K, 10.750" BOLT CIRCLE,
( CAN USE GM4401 when out of stock)
Add an addition refundable core charge of $155.00
Item #GM1A | | TC 13" DIAMETER, V8 GAS, DIESEL, THREAD 10mm X 1.5, 14K-16K LOW STALL, 10.750" BOLT CIRCLE, With poppet valve
Add an addition refundable core charge of $75.00
Item #GM20F | | TC 13" DIAMETER, V8 PASSENGER CARS, 13K - 15K STALL, 11.5" Bolt Circle
3 Rows of Ribs, Fixed Pitch Stator, (NOT FOR TRUCKS)
Add an addition refundable core charge of $75.00
Item #GM3 | | Torque Converter (remanufactured) 12.4" DIAMETER, L6 V8, 14K-16K STALL, 10.750" BOLT CIRCLE, NON LOCK-UP
(for heavy duty torque converter use GM350F; CRITICAL CORE send in your core and wave the core charge)
Add an addition refundable core charge of $120.00
Item #GM350 | | TC 12" DIAMETER, L6 V8, 14K-16K STALL, 10.750" BOLT CIRCLE, HEAVY DUTY, FURNACE BRAZED FINS
( CRITICAL CORE send in your core and wave the core charge)
Add an addition refundable core charge of $125.00
Item #GM350F | | 12" DIAMETER, L6 V8 METRIC THREADS 10mm X 1.5, 14K-16K STALL, 10.750" BOLT CIRCLE
Includes converter bolts
Add an addition refundable core charge of $35.00
Item #GM4401 | | 13 DIAMETER, 1500-1700 STALL, 11.5" BOLT CIRCLE, 6 Bolt Pads
V8 Engines, light & Medium Duty trucks
Item #GM6 | |
WASHERS & BEARINGS | Top |
| Description |
Buy |
WASHER KIT TH350 69-79 (with METAL WASHERS 44211B, 44232, 44235, 44244, 44251 and shim 44255A)
img#200 Item #44200 | | BEARING KIT TORRINGTONS 350 69-86
img#201 Item #44201A | | WASHER STATOR #2 .083" Thick 350 69-86
img#211 Item #44211A | | WASHER STATOR #3 .100 Thick 350 69-86
img#211 Item #44211B | | WASHER STATOR #1 .066" Thick TH350 69-78
img#211 Item #44211 | | SHIM STATOR .010" TH350 69-86
img#211 Item #44212A | | SHIM STATOR .015" TH350 69-86
img#211 Item #44212B | | SHIM STATOR .020 350 69-86
img#211 Item #44212C | | SHIM KIT STATOR 350/C 69-86 CONTAINS 6 SHIMS ( between .015", .020", .025", .030")
img#211 Item #44200F | | BEARING STATOR to DRUM TH350/C) (DRIVEN SPROCKET to CASE TH125/ 125C)
img#211, 280 Item #44211C | | BEARING DIRECT DRUM TO FORWARD DRUM 350 70-86
img#229 Item #44229 | | WASHER FORWARD CLUTCH HOUSING TO INPUT RING GEAR 350 3 TANG METAL 69-79
img#232 Item #44232 | | WASHER FORWARD CLUTCH HOUSING TO INPUT RING GEAR 350 3 TANG PLASTIC 79-UP
img#232 Item #44232A | | BEARING INPUT RING GEAR TO FRONT PLANET TH350 / TH350C
img#235 Item #44235A | | WASHER INPUT RING GEAR TO FRONT PLANET (4 TANG) 350
img#235 Item #44235 | | BEARING ( 2.540" O.D. without Lip) INPUT CARRIER TO REACTION SHAFT, CASE TO RING GEAR HUB 82-06
img#238 Item #D74238A | | BEARING ( 2.465" O.D. without Lip) INPUT CARRIER TO REACTION SHAFT AND CASE TO REAR HUB 700R4 4L60E 82-UP WHEN OUT USE 74238A
img#238, 255 Item #74238 | | WASHER SUN GEAR SHELL TO ROLLER RACE 4 INSIDE TABS ( Plastic )
img#244 Item #44244A | | WASHER SUN GEAR SHELL TO ROLLER RACE 350 4 INSIDE TABS (Metal)
img#244 Item #44244 | | WASHER OUTPUT RING GEAR TO REAR PLANET 350
img#251 Item #44251 | | BEARING OUTPUT RING GEAR TO REAR PLANET TH350 75-86
img#251 Item #44251A | | BEARING (Used) OUTPUT RING GEAR TO REAR PLANET TH350 1975-86
img#251 Item #U44251A | | SHIM OUTPUT to CASE TH350/C .020" Thick (each)
img#254 Item #44255A | | BEARING (GOOD USED) OUTPUT RING GEAR HUB TO CASE (O.E. BEARING WITH LIP) 350 69-86
img#255 Item #U44254 | |
|